Control mode: two sets (one is a temperature control table controller. One is shown on a computer).
The temperature control in 10 areas was divided into left, middle and right areas, and a total of 30 area temperature control tables were divided into left, middle and right areas.
Temperature control mode: p i d (ratio / area / differential) control interface: windows heating control: scr heating: k type heating limit: when heating temperature is added, limit the rising temperature per minute, 3 °5 ºC / min plus heating power maximum value: limit the heat transfer power / output power to show the temperature, the red color indicates the normal, the red color indicates the normal temperature, and the color indicates the normal.
Set configuration surface: set temperature, speed, police report value, correction value (must be code) pid adjustment surface: the pid setting value in each temperature area and the temperature display and setting temperature measurement calculated by pid are used to analyze the temperature and temperature of each temperature area by using the high temperature monitoring line to enter the international area, the temperature and time and the temperature area are used to analyze the temperature and temperature of each temperature area in order to analyze the temperature tolerance of each temperature area in order to analyze the temperature and temperature of each temperature area in order to analyze the temperature and temperature of each temperature area in order to analyze the temperature tolerance of each temperature area in order to analyze the temperature and temperature of each temperature area in order to analyze the temperature and temperature of each temperature area in order to analyze the temperature tolerance of each temperature area.
Warning mode:
1. The temperature limit is up and down.
2. Air pressure upper and lower limit alarm 3. Enter the upper and lower limit warning of the speed delivery.
. Safety and precautions
Thank you very much for purchasing our products. Before using them, please pay attention to the relevant matters mentioned in the instructions. Any improper operation may cause unexpected faults.
Safety precautions
Before installation, maintenance and inspection, please be sure to read this operating manual carefully. After you are familiar with the knowledge of machinery, safety information and all matters needing attention, you can use it correctly.
In this operating manual, the class of safety precautions can be divided into [danger] and [attention].
Danger a dangerous situation resulting from an operation error may result in death or serious injury.
Be aware that dangerous situations caused by operational errors may result in moderate or minor injuries and damage to objects.
Matters recorded on the notice may also have significant consequences depending on the circumstances.So by all means, be sure to follow both.
After reading, please place it in an accessible place around the machine.
Safe use
1. Precautions to prevent electric shock
dangerous
1, after the power OFF, must pass more than 2 minutes, to confirm the overvoltage test, can do wiring or inspection, otherwise may cause electric shock.
2. Make sure that the grounding wire in the power cord is connected properly, otherwise it may cause the danger of leakage or electric shock.
3. Wiring and inspection shall be conducted by professional electrician technicians.
4, do not use wet hands to operate the switch, otherwise it may cause electric shock.
5, the cable can not be damaged, strong pull, heavy weight, heavy clamp, otherwise may cause electric shock.
2. Precautions for fire prevention
Pay attention to
1. In case of internal electrical component failure, the main power supply of the machine should be cut off to avoid the fire caused by the continuous inflow of large current.
3. Precautions for injury prevention
Pay attention to
1. Do not apply the voltage on each terminal other than the wiring diagram, otherwise it may cause rupture and damage.
2. Do not connect the terminals by mistake during connection, otherwise damage or other objects may be caused.
3. Do not reverse polarity, otherwise damage or other objects may be caused.
4. The heat sink, regenerative resistance and various motors of all electrical components may be in a high temperature state during electrification or for a short time after power supply is cut off. Please do not touch them to avoid burns.
4. Other precautions
Please pay attention to the following precautions to avoid failure, danger or electric shock caused by wrong operation.
(1) transportation and installation
Pay attention to
Please handle according to the weight of the product in the correct way.
2. When installing, please install in the place that can bear the weight according to the instructions.
3. Do not allow conductive foreign bodies such as metal sheet, or combustible foreign bodies such as oil to invade the electric parts or the internal of various motors.
Please keep and use under the following circumstances:
Environmental conditions
Electrical components, servo motors, motors
Ambient temperature 0 to +40ºC (non-freezing state)
Ambient humidity up to 80 KP (without condensation)
Storage temperature from -15ºC to +60ºC (non-freezing state)
Keep the humidity below 90 KP (without condensation)
Place inside (where direct sunlight does not reach)
Avoid corrosive gas, ignition gas, oil mist, dust environment.
Pay attention to
1. Do not touch the rotating part of the motor during operation.
2. Do not use hammer to strike the servo motor shaft connector, or it may cause the fault detection.
(2) about wiring and electrical component replacement
Pay attention to
1. Please connect the wiring correctly and accurately, otherwise it may cause electrical short circuit or burn out.
2. Before replacing the electrical parts, please pay attention to whether there are directional protection devices when installing the electrical parts, so as to avoid excessive voltage and damage of other electrical parts.
3. When replacing photoelectric, PC board, driver and other electrical products, please first determine its polarity, phase and voltage value, or it may cause electrical components or electrical short circuit fault.
4. When replacing the motor, the balance degree of the installed motor and the tightness degree of the passive object should be determined, otherwise the stability and life of the motor may be caused.
(3) about trial run and adjustment
Pay attention to
1. Before operation, please first confirm whether the external voltage is in the stable ac220v-ac235v. Too low or too high voltage or unstable voltage input may lead to the internal precise electrical components or abnormal operation.
2. Extreme changes in mechanical specifications or adjustments will cause mechanical instability, so absolutely avoid.
(4) about the use method
Pay attention to
1. Electrical accessories, PC board, fiber optic controller, drive, servo motor, step motor, frequency converter, PLC, operator interface (man-machine interface), please do not do decomposition repair, otherwise warranty is not allowed.
2. Please do not modify the electrical and mechanical structures without permission. Any damage caused by modification is not guaranteed.
3. Damage caused by improper use is not covered by the warranty.
4. Damage caused by too low or too high external voltage is not covered by the warranty.
(5) handling of abnormal alerts
Pay attention to
1. In case of abnormal occurrence, check the reason first, confirm safety, reset abnormal alarm, and then start operation.
2. After the instantaneous power failure and power resumption, the machine may suddenly operate, so please do not approach the machine at this time.
(6) about maintenance
Pay attention to
1. Gear oil of 20 # --40 # shall be replaced once a year for reduction gear. Please do not replace with other oil.
2. The CAM gear is buttered once a month, and the universal bearing is buttered once a week.
3. Add oil once a day to the red paint, joints and sliding surfaces.
4. Remove the electrolyte that may splash on the sliding surface at any time. Please lubricate it daily and keep an oil film to prevent machine wear and erosion.
5. When the machine is shut down for more than one day, please fully lubricate and clean before the shutdown, so as to avoid the formation of particles during the solidification of the electrolytes not cleared on the machine, and the parts will be worn or damaged when starting up.
6. Use alcohol to wipe the claws and guide mold of vegetable seed every day.
7. The photoelectric device shall not be wiped with alcohol, only with a clean dry cloth.
8. We are subject to change and improvement of electrical or mechanical structures without prior notice.(the machine structure after the improvement is not modified before the improvement of the machine for additional installation and warranty, if necessary, the price is discussed separately.)
3. Machine installation method
1. Check whether the mechanism is damaged or deformed due to improper loading and unloading.
2. Move the machine to the position, adjust the foot post bolts at the four corners of the machine, make the wheels off the ground and calibrate the machine with a leveler.Keep the machine plane level before locking the nuts of the pad bolts.
3. Remove the tape and rope used for fixing. Please do not connect the power supply at this time.
4. Open the electrical box and confirm that the socket accessories are not loose.
5. Make sure that the electrical accessories are not immersed in water and oil and the insulation is good.
6. Wipe the anti-rust oil on the machine and each feed part.
7. Put # 40 lubricating oil on the parts with red paint on the machine.
8. Press the switch of the power box to the OFF position.
9. Connect to 220V power supply and make sure the green or yellow connection is grounded.
10. Power supply ON, no fuse switch ON, make sure that the DC24V voltage is normal and the first and second red indicators ON the power supply are ON, indicating that the power supply is normal.
11. Check whether the RUN light (green) on the PLC is on. The light indicates that it is normal.
12. Check the POWER(POWER supply) lamp on PCB board to see if it is normal.
I. equipment summary
The equipment can be used to produce solid state capacitor element containing leaching process.Will rack car into the supply box and the move sent to the 1 contains the leaching tank, the vacuum contain leaching and then moved to the drying furnace, 3 period of drying process, and then moved to contain the leaching tank, 2 after vacuum including dip again moved to wipe again station, wipe away excess electrolyte then move to the 2 points 3 period of drying, drying furnace, then remove to receive a furnace on the automatic containing leaching of cleaning equipment.
Each servo position is set
The set value of this machine is as follows
1. The velocity is divided into high speed and low speed and the origin velocity. The origin velocity (JOG) is not recommended to be modified.High speed is used for no-load operation (when the gripper is open) and low speed is used for moving operation (when the gripper is clamped).
X, Y, Z value of each servo position, the current position set on the aircraft is the best position, modify the range to no more than 2mm.In terms of the z-axis, when adjusting the feeding and storage area, it will be changed due to the change in the speed of the throttle valve of the oil pressure cylinder. Therefore, it is strongly recommended that when the throttle valve of the oil pressure cylinder is changed, the height of the z-axis of this part shall be readjusted.
Troubleshooting:
1. If the fixture plate is tilted, the position is Z1, Z2 and Z3 and the fixture is overlapped when falling (not taken out) or the guide rod is stuck, please turn the automatic/manual switch button to the manual position and enter the fault shaft position. If the origin light is on, press the upper point to return to the top point.If the original light is not on, please JOG- after rising a little, according to the origin of the return, can be again in order to run.
In case of pressing the emergency stop button or general fault operation, it is necessary to press the reset button and press the start button again. In this way, the servo motor (conveyor belt) can be started again smoothly and normally after being forced to stop operation.
Adjust the liquid level of immersion tank and upper storage tank
As shown in the attached figure: adjust the liquid level of the dip tank to adjust the separation card of the optical fiber. During the adjustment, please first loosen the screw on the side, and then tighten the screw after adjusting the separation card. The current standard height is 5mm.
Upper liquid storage bucket: three optical fibers, the upper part is too high, when the optical fiber induction, the upper liquid storage bucket supply valve will be forced to close, the middle is normal, usually added to the liquid level, the bottom is insufficient, such as continuous induction, also means the lower electrolyte bucket is insufficient, please add the electrolyte.
OUR COMPANY INFORMATION
Dongguan city Jinyao precision Equipment co., LTD is one of Enterprise combining develop, produce and sale. Established in 1980, already have 30 years experience to produce: precision Hot-air drying oven; IR/UV deliver drying equipment; environmental test equipment; printing machine; automation industrial equipment etc.
Our company always keep the aims that provide high quality product; quick service attitude and the great design. We keep the company spirit that has advance technology and high quality team. Our product receive a lot of client trust, and stand firmly front of others.
Dong Guan YUTSAI precision device enterprise LTD. is registered capital achieve ten million RMB. It has 4800 square meters factory. More than three million RMB fixed assets. Value of output achieve 24million RMB each year.
We has the steady domestic clients such as: FOXCONN, HuohYow, FU BROTHRT industrial company, HUAXIN technology company, PUYAO group etc. It's all about more than 500 company include Domestic ,foreign and military enterprises. We also has the long-term relationship with Thailand, India and England.
The company toward higher, farther, more perfect operating system. the Taiwan Head Company as the axis, and we make efforts in mainland market development.
FAQ
1. Can you customize the product?
Yes, we can customize any products according to customer's requirements.
2. Which payment terms are you doing?
PayPal, West Union, T/T, (100% payment in advance.)
3. Which shipment is available?
By sea, by air ,by express or as your requirement.
4. Which country you have been exported?
We have been exported to many countries, all most all around the world, like Malaysia, Vietnam,
Thailand, United States, France, Spain, Mexico, Dubai, Japan, Korea, Germany, Portland Etc.
BUSINESS CARD
Contact us
If you want to know more detailed information about our products , please feel to contact us at any time !
Contact US :
Contact : QQ:3136414748
Wechat&Skype: +86-13533280147
Whatsapp&Phone Number:+86-13533280147
E-mail: yutsai168@yutsai.com.cn
Http:// jinyao-equipment.en.made-in-china.com
Http://jinyao-equipment.en.made-in-china.com
Dongguan Jinyao Exactitude Equipment Co., Ltd
Address: Jingfu Road No 36, xiabian village, changan town Dongguan City China
WELCOME TO CONTACT US !
){kind=link}